Tail lights inter-working with RV towing connection

 Tail lights inter-working with RV towing connection

        The very purpose of this car, be flat-towed by a RV. I looked around and discovered that a very limited number of cars can be flat-towed safely with no risk of damage to transmission/differentials.

        In summary, most automatic transmission vehicles are not candidates, so I was left looking for a cheap option, ideally 4 wheel drive, in a small list of options. This old manual 1995 Jeep Wrangler popped up in my search, which had already been flat-towed and even included the towing setup, arms, etc.

        The previous owner made an attempt to use the car's own rear lights to carry the RV's lighting, but ended up using an additional light rig that needs to be installed from front to back, outside of vehicle. This rig has two simple lights that are attached to the rear bumper with magnets. I used this for the first few trips while I investigated what would take to use the car wiring and lights.

        One thing that I suggest to anyone getting into electric work is to first of all, get yourself a maintenance manual or specific electrical diagrams of circuit that is been analyzed.

        I did some research online and found this website where I was able to grab all electrical diagrams for this vehicle, I found it online for $20. Without an electrical diagram, I would not be able to figure this out.

        When looking into the diagram for "external lights", observed that both rear turn/stop lights were connected together by the turn switch in the steering column, when lever rest in the OFF position (center, no turn lights activated).

        Because of this small detail, if an external source of power (RV) is connected to the vehicle's rear turn/stop wiring, a malfunction happens as both wires for right and left turn are short circuited.

        Needless to say that each right and left circuit needs to work independently, while the parking lights work both right/left simultaneously. As seen below, parking lights are connected together and in theory, should work without and modifications. However, I implemented the same changes I did to the turn/stop lights, just in case.

        IMPORTANT : Before starting any work, make sure that you disconnect the car's battery.

        

        Before next step, let's talk about the actual solution for the issue and what a "diode" actually does.

        As discussed, we need to have independent connections to the turn/stop lights, so the RV can be connected and work properly when a left turn or right turn signal is used. The easiest way to accomplish this is with a electronic component called "diode", which is a semiconductor built as such that the electrical current can only travel in one direction. Showing below the representation of a diode:

        Using this principal of one direction flow, we can easily implement an "isolator" circuit, as shown below:

        This configuration allows both RV and vehicle to power the rear lights, installed under dashboard near the connector coming from steering wheel column (including turn sign lever switch).

        When choosing a diode for this purpose, considerations should include the max direct current and max reverse voltage. The max current should be higher than what the light bulbs can consume and the max reverse voltage higher than 12 volts.

        Diode 20SQ050 was selected, with max current of 20A and max reverse voltage of 50 volts, from Amazon at $8 for 25 pieces.

        Installing this solution requires some level of proficiency in simple electrical work, including splicing, soldering and isolating wires.

        The wires to be spliced runs in the harness going from dashboard to the rear of vehicle. This bunch of wires packed together runs inside the steel frame of vehicle on the driver's side and it can be "fished" at different places. In my case, I decided to work under the dashboard, right at the plug connecting wires coming from the turn switch and hazard switch in the steering wheel, as well as the wire coming from the parking light switch.

Next, sharing few pics with details of installation.

TO BE CONTINUED

Safety cutoff switch

 

        Used to modern cars, with state of the art burglar alarms? Well, not on a 1995 Jeep that in fact, has nothing for deterring intruders. That's when a simple solution can be added, using just a toggle switch and few feet of electrical wires.

        This is a simple scratch representation of the ignition circuit in this car. Inserting a switch on wire that feeds power to the ignition coil is a simple way to add some protection for non-authorized engine start.

        Find the ignition coil:

        Unplug the connector to the coil, will be easier to splice the wire.

   

        There are two wires coming to this connector, cut the wire that powers the coil and splice it into wires going to the cutoff switch in the cabin. Usually, this wire has colors, or you can check voltage on the pins of removed connector with a volt-meter or a simple test jig that I will show next . Hot wire coming from ignition key will have 12V+ (or light bulb of test tig is lit), while the other pin will not.

In order to test this, you need the car key on the "ON" position (not starting engine). There are 4 positions on a car key:

1) OFF/LOCK

2) ACC - Accessories/UNLOCK

3) ON - Ignition

4) START (temporary)

        Install the cutoff switch in dashboard, hidden but easy access to toggle, connected to the two wires from the splicing in coil connection.

        One thing to note, I often forget that this switch exists and try to start the engine, which will not start, as expected. Then I realize I forgot to turn ON the switch and car starts. If you insist too much with the switch OFF, you may end up discharging the car's battery or before that, introduced too much fuel in intake that engine won't start. If this happen, let the car sit for couple minute for fuel to evaporate.

        Next, showing the actual connections, running the cable and installing the switch.

        TO BE CONTINUED.

        

Turn-Parking-Marker lights LED upgrade

        Sounds easy right, just plug and play?

        Not really, this project involved trying few different parts from Amazon, having to get the vehicle electric diagrams in order to study and figure out how to make it work.

        The main reason for issues on this and many other upgrades for this vehicle are due to the old electrical design and parts present in this vehicle.

        Flashing relays, for instance, uses bimetallic strips design, instead of electronic oscillator/timer relays. These thermal driven devices requires minimum currents for operation, in fact, it only works if load is present. The load current drives the oscillating process and it somewhat dictates the oscillation frequency. For instance, loads with lower current will oscillate in lower frequencies while higher currents operates in higher frequencies. 

        Because a minimum load current is required for operation, LED loads draws way less current than incandescent bulbs and it is not enough for these flasher relays to work.

        In this vehicle, flasher relays are used for turn and emergency lights.

        Typical OEM flasher relays:

        How it looks internally:

    

        While electronic flashers are usually smaller and retro compatible for easier replacement.

        Typical electronic flasher:

        

    

  

        For the upgrade to LED lights, two relays had to be replaced with modern electronic parts in order to have all turning and emergency functionalities.

        These are plugged into the fuse tray, located under the dashboard near the steering column.

        

        Replace old flashers with this electronic flasher from Amazon:

        Note that although it fits and plug replace the old relay, the electronic designs require an                additional ground wire, which you can connect to any ground available near the fuse tray, usually any screws docked to the car's metal structure. In my case, I decided to splice and extend this ground wire to give me better options for connection.

Upgraded with the following products: